Offenhauser 5997DP Toyota 1900/2000/2200cc OHC Dual Port Intake Manifold

$399.99

Recent dyno and road tests have proven the Dual Port can give these Toyotas as much as a 20% HP boost over the stock manifold without sacrificing fuel economy. MPG gain was as much as 15%.

5997-DP Application: 1970-74 (also fits 18RC) (Stock 2 STG Carb)

8 in stock

Dual Port Series

"The patented Dual Port is our STREET PERFORMANCE/ECONOMY DESIGN. in the Mini's, the primary section boosts the fuel mixture to nearly the "speed of sound", about 3 times faster than normal velocity. This positively gives each cylinder a full fuel charge every time to smooth out the power stroke. When engine or driver demand cuts in the secondaries, a cold (over 30° colder) and dense mixture is sent down the secondary runner to be rammed into the combustion chamber by the sonic flow to the primary runner. This adds up to 15-30% more horsepower, quicker throttle response, extended RPM range, better gas mileage, Quicker starting, reduction to exhaust emissions.

The two barrel mini Dual Ports come standard (order "DP") to accept the stock 2 stage carburetor. However, as an alternative, most can be drilled to accept the Holley 5200 series (order "DPH") or the Weber 32/36 series (order "DPW")"

"DPH" ACCESSORIES (HOLLEY 5200)

Some Mini Dual Ports (including Datsun. Toyota. Chevy Luv and Ford Courier), which have been drilled for the Holley 5200 carb will usually require a 1" carb riser No. 6176 in order for the carb linkage to clear the manifold. Also available is a linkage accessory kit (No. 6230) for CABLE OPERATED
applications or CABLE CONVERSIONS when installing the "DPH" manifold. A Universal Foot Throttle Kit (No. 6244) completes the installation where a change of throttle linkage is desirable. The new Holley Datsun 5200 carbs also work very well with the Dual Port. In this case, order the "DPH" and substitute our No. 6176 in place of the Holley carb plates supplied with the carb. The linkage accessory kit is not necessary.
PART NO.
6176- 1" Holley Carb Riser Recommended - See above
6230- Universal Cable Linkage Accessory Kit Recommended - See above
6232- 1" Offset Riser (Used in place of No. 6176 on later Courier/ Mazda OHC Engines where cam cover is wider than cylinder head side surface)
6235- 1" Offset Holley 5200 Carb Adapt. (Holley 5200 to stock DP base. Fits Courier, Datsun, Luv, Toyota, etc. with carb base measurement of 3-1 /8" x 1-3/4 ". See Carb Conversion Chart on page 8.)
6244- Universal Foot Throttle Kit See above

"DPW" Accessories (Weber 32/36)

The Weber 32/36 will not usually require any accessories. A Weber riser plate (No. 6234) is included with the "DPW" to ensure
linkage clearance. Some minor linkage adjustments may be necessary and a Linkage Accessory Kit No. 6230 is available
if required.
PART NO.
6230- Universal Cable Linkage Accessory Kit. Available if cable conversion is necessary.
6232- 1" Offset Riser (used in place of No. 6234 on late Courier/Mazda OHC engines where cam cover is wider
than cylinder head side surface)
6234- Weber Riser Plate - Included with "DPW" Manifold (5/16" for linkage clearance)
6236- 1" Offset Weber 32/36 Carb Adapt. (Weber 32/36 to stock DP base. Fits Courier, Datsun, Luv, Toyota, etc. with carb base measurement of 3-1 /8" x 1-3/4". See Carb Conversion Chart on page 8.)
6244- Universal Foot Throttle Kit. Available if Cable Conversion is necessary.

Brand

Offenhauser

Offenhauser Intakes, Manifolds, Valve Covers, Heads, and More!

White Owl Speed is the newest distributor for Offenhauser. We have exclusive merchandise and parts that have not been available for 60 years! We are constantly listing new parts and making new inventory available so make sure you check back often! Offenhauser was established in 1946 by Fred C. Offenhauser and Fran Hernandez. All of Offenhauser's parts are cast and machined in California. All Offenhauser parts are forged using a hand-carved wooden pattern at Bell foundry in South Gate, California and machined at the Offenhauser Shop In Downtown Los Angeles. Offenhauser is one of the oldest premium automotive parts manufacturers in the world operating for over 70+ years continuously.

Reviews

There are no reviews yet.

Be the first to review “Offenhauser 5997DP Toyota 1900/2000/2200cc OHC Dual Port Intake Manifold”

Your email address will not be published. Required fields are marked *

Dual Port Series

The patented Dual Port is our STREET PERFORMANCE/ECONOMY DESIGN. in the Mini’s, the primary section boosts the fuel mixture to nearly the “speed of sound”, about 3 times faster than normal velocity. This positively gives each cylinder a full fuel charge every time to smooth out the power stroke. When engine or driver demand cuts in the secondaries, a cold (over 30° colder) and dense mixture is sent down the secondary runner to be rammed into the combustion chamber by the sonic flow to the primary runner. This adds up to 15-30% more horsepower, quicker throttle response, extended RPM range, better gas mileage, Quicker starting, reduction to exhaust emissions.

The two barrel mini Dual Ports come standard (order “DP”) to accept the stock 2 stage carburetor. However, as an alternative, most can be drilled to accept the Holley 5200 series (order “DPH”) or the Weber 32/36 series (order “DPW”)”

“DPH” ACCESSORIES (HOLLEY 5200)

Some Mini Dual Ports (including Datsun. Toyota. Chevy Luv and Ford Courier), which have been drilled for the Holley 5200 carb will usually require a 1″ carb riser No. 6176 in order for the carb linkage to clear the manifold. Also available is a linkage accessory kit (No. 6230) for CABLE OPERATED
applications or CABLE CONVERSIONS when installing the “DPH” manifold. A Universal Foot Throttle Kit (No. 6244) completes the installation where a change of throttle linkage is desirable. The new Holley Datsun 5200 carbs also work very well with the Dual Port. In this case, order the “DPH” and substitute our No. 6176 in place of the Holley carb plates supplied with the carb. The linkage accessory kit is not necessary.
PART NO.
6176- 1″ Holley Carb Riser Recommended – See above
6230- Universal Cable Linkage Accessory Kit Recommended – See above
6232- 1″ Offset Riser (Used in place of No. 6176 on later Courier/ Mazda OHC Engines where cam cover is wider than cylinder head side surface)
6235- 1″ Offset Holley 5200 Carb Adapt. (Holley 5200 to stock DP base. Fits Courier, Datsun, Luv, Toyota, etc. with carb base measurement of 3-1 /8″ x 1-3/4 “. See Carb Conversion Chart on page 8.)
6244- Universal Foot Throttle Kit See above

“DPW” Accessories (Weber 32/36)

The Weber 32/36 will not usually require any accessories. A Weber riser plate (No. 6234) is included with the “DPW” to ensure
linkage clearance. Some minor linkage adjustments may be necessary and a Linkage Accessory Kit No. 6230 is available
if required.
PART NO.
6230- Universal Cable Linkage Accessory Kit. Available if cable conversion is necessary.
6232- 1″ Offset Riser (used in place of No. 6234 on late Courier/Mazda OHC engines where cam cover is wider
than cylinder head side surface)
6234- Weber Riser Plate – Included with “DPW” Manifold (5/16″ for linkage clearance)
6236- 1″ Offset Weber 32/36 Carb Adapt. (Weber 32/36 to stock DP base. Fits Courier, Datsun, Luv, Toyota, etc. with carb base measurement of 3-1 /8″ x 1-3/4″. See Carb Conversion Chart on page 8.)
6244- Universal Foot Throttle Kit. Available if Cable Conversion is necessary.

Share This